Shower Glass 1
Shower Glass 2

Architectural Glass / Shower Glass

Shower Glass

Shower glass is the safety glass in the doors and panels around a shower. Tempered glass is used: it is much stronger than ordinary glass of the same thickness and breaks into small, blunt pieces rather than sharp shards. The glass is cut, edge-worked and drilled for hinges and handles, then tempered last.

Technical Features & Advantages

  • Tempered safety glass, much stronger than ordinary glass
  • Breaks into small, blunt pieces
  • Cutting and hinge and handle holes are done before tempering
  • Thickness is chosen to suit the enclosure system and panel size
  • Coated types that reduce limescale build-up are available
  • Heat soak tested glass can be requested against nickel sulphide risk

How is shower glass made?

Shower glass is made from flat glass. It is cut to size, edge-ground and drilled for hinges, handles and clamps, then heated in a tempering furnace and cooled rapidly with air on both sides. Tempered glass cannot be cut or drilled afterwards, so all dimensions and hole positions must be final before tempering.

Uncoated shower glass wears over time: whitish, rough spots form on the surface and hold more limescale and dirt. So shower glass with a metal oxide coating is also made. The coating makes water run off quickly and reduces limescale marks. The coated side is fitted facing the inside of the shower.

How thick should shower glass be?

No single thickness suits every shower system. It depends on the enclosure type (framed or frameless), the door and panel size, and the load the hinges and clamps can carry. The thickness specified by the enclosure system maker is used. One glass manufacturer makes shower glass in 4, 6, 8 and 10 mm.

When replacing a broken pane, measure the old glass and order the same thickness. Hinges and clamps suit a given glass thickness, so the new glass must match the old in thickness, hole positions and edge work.

Why does shower glass shatter?

Tempered glass occasionally breaks with no impact. The main known cause is tiny nickel sulphide particles left in the glass during manufacture, which expand over the years and can break it long after installation, leaving a figure-eight mark at the centre of the break. Other causes come from installation: a small edge chip from handling or fitting grows and breaks the whole pane, and glass pressed against metal in a hinge or clamp, with no room to expand, is stressed as it heats and cools.

The edge is the weakest part of tempered glass; a door edge striking a wall, worktop or another pane can break it. Broken tempered glass falls apart into small pieces.

  • Glass that has passed the EN 14179 heat soak test can be requested to reduce the nickel sulphide risk
  • The glass should sit on gaskets and setting blocks, not directly against metal parts
  • Glass with a chipped or damaged edge should not be installed
  • The door edge should be kept from striking a wall or another pane

How do you clean shower glass and prevent limescale?

Removing water with a squeegee or towel after every shower reduces limescale marks. Wipe the glass regularly with a soft cloth and water or with a shower glass cleaner; abrasive cleaners, wire wool and hard sponges scratch the surface and are not used.

A water softener reduces limescale but not silica, which can stick to the glass and leave marks, so softened water still needs regular wiping. For coated shower glass, the manufacturer says water-repellent products applied afterwards are not needed.

Shower glass at Salt Cam

Salt Cam makes and sells shower glass. The company has operated since 1930. Its head office is in Mersin and its production plant is in the Mersin Tarsus Organised Industrial Zone; it has 51,000 m² of covered area in total. Its TSE (Turkish Standards Institution) certificate of conformity to TS EN 12150-2, the Turkish edition of the tempered safety glass standard, is on the Certificates page.

Prices depend on thickness, size, number of holes, edge work and quantity, and change often, so the website has no list price. For a quote, send a drawing with the dimensions and hole positions to +90 324 324 39 39 or saltcam@saltcam.com.

Causes of shower glass breakage and precautions

CauseHow it happensPrecaution
Nickel sulphide inclusionAn inclusion in the glass grows over time and can break it years laterGlass that has passed the EN 14179 heat soak test
Edge chipA chip from handling or installation grows over timeCareful handling; do not install chipped glass
PinchingThe glass touches metal in a hinge or clamp and cannot expandGaskets and setting blocks, correct glass thickness
Edge impactThe door edge strikes a wall or another paneInstallation that stops the door from striking

Causes are compiled from manufacturer and encyclopedia sources on the spontaneous breakage of tempered glass.

Applications

  • Shower doors
  • Fixed shower panels
  • Frameless walk-in shower screens
  • Bath screens
  • Replacing broken shower glass
  • Hotel, dormitory and hospital bathrooms

Related standards

EN 14428
Sets functional requirements and test methods for shower enclosures for domestic use, including hotels, dormitories and hospitals.
TS EN 12150-1
Covers dimensional tolerances, flatness, edge work, fragmentation and physical properties of flat tempered safety glass used in buildings; refers to the shower enclosure standard EN 14428.
TS EN 12150-2
Product standard for tempered safety glass: sets how conformity of production is assessed and covers CE marking.
EN 14179
Defines the heat soak test applied to tempered glass to lower the chance of spontaneous breakage caused by nickel sulphide inclusions.

Frequently asked questions

How thick should shower glass be?

It depends on the enclosure system; no single thickness fits every enclosure. Framed or frameless design, door size and the load on the hinges decide it. One glass manufacturer makes shower glass in 4, 6, 8 and 10 mm. When replacing a pane, measure the old glass and order the same thickness.

Why does shower glass shatter on its own?

The best-known cause is a nickel sulphide inclusion in the tempered glass, which grows over time and can break it years later. An edge chip from installation, glass pinched in a hinge or the door edge striking something can also break it. Broken tempered glass falls into small, blunt pieces.

How can shower glass breakage be prevented?

To reduce the risk, protect the glass edge and fit the glass on gaskets and setting blocks so it does not touch metal directly. Do not install glass with a chipped edge, and stop the door edge from striking a wall or another pane. Against nickel sulphide risk, you can request glass that has passed the EN 14179 heat soak test.

How do you remove limescale from shower glass?

Wipe shower glass regularly with a soft cloth and water or a shower glass cleaner, never with abrasive cleaners, wire wool or hard sponges. A squeegee or towel after every shower reduces limescale marks. A water softener does not remove silica, so regular wiping is still needed.

Can I replace just the glass in a broken shower enclosure?

Yes, the glass alone can be replaced. You need the width, height and thickness of the pane, the positions of the hinge, handle and clamp holes, and the edge work. Tempered glass cannot be cut or drilled afterwards, so these must be complete. If possible, use the enclosure maker's glass dimensions.

What affects the price of shower glass?

Shower glass prices depend mainly on thickness, size, number of holes, edge work, coating and order quantity. Extra processes such as heat soak testing also affect the price. Salt Cam quotes on dimensions and processing rather than a fixed list, because glass prices change often.

Request a quote for price and sizes

Glass prices change frequently, so we do not publish prices. Send us your sizes, glass type and quantity and we will send a quote.

Related products

Sources

  1. Tempered glass, Vikipedi
  2. Pilkington Toughened Glass, Pilkington UK (NSG Group)
  3. SGG TIMELESS ürün broşürü, Saint-Gobain Glass
  4. Caring for your ShowerGuard glass, Guardian Glass
  5. BS EN 14428:2015+A1:2018 Shower enclosures. Functional requirements and test methods, BSI
  6. BS EN 12150-1:2015 Thermally toughened soda lime silicate safety glass, BSI
  7. Frameless Shower Enclosures Design Guide DG02-21, National Glass Association

Written by: Salt Cam Technical Team · Last updated: 16.11.2026